MBIQ-S Tuning Sensor for Shimano Steps E5xxx - E8xxx E-Bikes with SM DUE10
New
Pre-order
Sold Out
MBIQ-S Tuning Sensor for Shimano Steps E5xxx - E8xxx E-Bikes with SM DUE10
AVAILABILITY: In stock
PRODUCT TYPE: Shimano
BRAND: MBIQ
134,90 €
VAT included.*
PRODUCT INFORMATION
Comparison
Tools
Reviews
warnings
Payment & Shipping
PRODUCT INFORMATION
MBIQ-S Tuning Sensor for Shimano Steps E5xxx - E8xxx E-Bikes with SM DUE10
A microcontroller-based sensor solution for e-bikes with Shimano Steps mid-drive motors. This tuning tool completely removes the 25 km/h speed limit, allowing you to finally enjoy the full potential of your Shimano motor. The MBIQ-S is therefore reduced to the absolute essentials: removing the speed limit – there are no other functions. Installing the tool is simple, as you essentially just need to replace the e-bike's speed sensor with the MBIQ-S.
You don’t need an extra battery for the MBIQ-S.
Functionality
After connecting the tuning tool, the MBIQ-S analyzes the current speed profile and forwards manipulated sensor values. Speeds above 25 km/h are blocked for the motor firmware, thus removing the motor's speed limit. Important note: Due to this special functionality, your e-bike's speedometer will no longer display the correct speed above approximately 22 km/h. To be precise, the displayed speed will always be ≤ 25 km/h.
Incidentally, the evaluation of the engine software is not affected in any way by the manipulated values / no detection.
Three operating modes
Unlike previous models, the MBIQ-S can be programmed by the customer. The individual operating modes can be activated by specific wheel movements when turning on the e-bike. You can choose between three different operating modes:
Tuning is always switched on (the speed limit is permanently removed; from approx. 25 km/h the displayed speed no longer corresponds to the actual speed).
Tuning is permanently switched off (the speed limit is not removed, motor support up to 25 km/h with real speed display).
Tuning based on power-on condition: To activate tuning, the magnet must be in front of the sensor for approximately 3-4 seconds during boot-up; otherwise, tuning is deactivated. This can be useful, for example, if you want to deactivate tuning before a workshop visit (the sensor solution is virtually invisible in this case).
Easy installation
The installation of this tuning tool is easy, as you basically only have to replace the original speed sensor with the MBIQ-S. You'll find the sensor on the rear frame, often next to the quick-release axle. Depending on the manufacturer, the sensor cable is often routed through the frame. The connector end is plugged into the engine compartment, which is usually protected by a plastic cover.
Depending on the manufacturer and model, it may be necessary to remove the motor to pull out the sensor cable and insert the MBIQ-S. On some e-bike types, the sensor cable runs through the frame and must be carefully pulled out. The MBIQ-S cable must then be routed through the frame in the same way using the included pull wire.
Since the look of the MBIQ-S is absolutely neutral, your e-bike will not be visually changed in any way by the tuning.
Tip: We recommend keeping the e-bike's original sensor so that you can restore the bike to its original condition if necessary.
Robust & resistant to moisture
Compared to previous models, the quality of the housing components in the MBIQ-S has been significantly improved. Thanks to the electronics encapsulated in the sensor, the MBIQ-S is extremely resistant to dirt and moisture.
MBIQ-S Tuning Sensor for Shimano Steps E5xxx - E8xxx E-Bikes with SM DUE10 – Compatibility
This tuning tool is compatible with all common Shimano e-bike mid-engines: Steps E8xxx, Steps E7xxx, Steps E6xxx, E5xxx etc. with SM DUE10.
Also compatible with Di2.
Tested up to FW 4.9.0.
Delivery
MBTK-S tuning kit sensor cable with original connectors (cable length approx. 70 cm)
Installing an e-bike tuning chip in your e-bike may require special tools . Please check beforehand whether you need to open the motor compartment to access the motor's connectors. This applies particularly to products in the categories of modules , kits , dongles , and sensors.
If you don't opt for a tuning solution that requires installation in the engine compartment ( such as a tuning box or software ), you won't need the necessary tools. You'll find further tips in our guide .
Reviews
The EBikeTuningShop and the EBikeTuningBlog regularly inform you about the latest e-bike and e-scooter tuning products and solutions. You can subscribe to the free newsletter here:
warnings
warnings
Important information on tuning measures for e-bikes and e-scooters
We expressly point out that any modification to e-bikes and e-scooters – whether through hardware tuning (e.g. tuning chips, dongles, sensor adapters) or software tuning (e.g. apps, programs or USB tools) – can have consequences.
Tuning measures on e-bikes and e-scooters mean that they are no longer permitted for use on public roads as defined by the StVZO (Road Traffic Licensing Regulations). Legal use is therefore only possible on private property or - if permitted - in competitions. Riding an e-bike or e-scooter modified by tuning measures on public roads can lead to criminal liability for driving without a license (Section 21 of the Road Traffic Act) and driving without insurance (Section 6 of the PflVG). Tuning measures on e-bikes can lead to the loss of warranty rights and manufacturer guarantees. Furthermore, tuning measures can lead to the loss of insurance coverage and benefits from accident victim assistance in the event of an accident. The e-bike (or e-scooter) modified by tuning measures is subject to additional stress due to the higher speed, which can lead to safety risks.
Payment & Shipping
Delivery time, shipping costs, minimum order value and payment methods:
Delivery time:
The processing time for physical products generally only begins after payment has been received . Within Germany, it usually takes 1–3 business days . In exceptional cases, processing may take up to 8 business days . Delivery times to other countries may vary.
Please note: You will only receive a DHL shipment confirmation once the shipment has been scanned for the first time at the parcel center. Only from this point onward will the shipment be trackable.
Due to high demand, ongoing incoming goods, or anticipated short-notice restocks, some products may experience longer processing times. We appreciate your understanding.
Note regarding digital products/license codes: License codes and license keys are not sent by mail, but by email . Processing begins only after payment has been received. Please note that instant bank transfers do not automatically result in a direct bank credit, and in some cases, credit card payments may also experience delays in payment reconciliation. The respective license code will then be generated and sent. This may take several hours in some cases. If you do not receive a license code, please always provide us with the order number in the format xxx-xxx-xxx.
For customers from Switzerland: For deliveries to Switzerland, we recommend a separate service.
Shipping:
Shipping costs for Germany are €4,90; shipping is waived for orders over €180. For countries within the EU, shipping costs are €12,90; shipping is waived for orders over €2.000. We currently do not ship to countries outside the EU. We also do not ship to the USA, France, or Canada (including any overseas territories). We ask that you bear the costs of any return shipments yourself. Please note that customs duties may apply in countries outside the European Union.
Minimum order value:
The minimum order value is €25. Only above this amount are advance payment, PayPal, and bank transfer available as payment methods.
Maximum order value:
The maximum order value for orders outside the EU is €1.000. The maximum order value within the EU is €12.500.
Payment in advance via bank transfer:
Please transfer the total amount, including your order number, to our account, which was communicated to you in the confirmation email. Please note that transfers within Germany can take up to three business days. Transfers from abroad, especially from Austria, usually reach us very quickly. Transfers from other countries can take slightly longer on average.
Payment in advance via Paypal:
At the end of the ordering process, you will be redirected to the PayPal page. There you can initiate your payment. Once the PayPal transaction is complete, your order status will change in the shop. The goods will then be shipped as soon as possible.
Do you need help choosing the right tuning product or have questions about ordering, shipping, or invoicing? Here you'll find the quickest way to a suitable answer.
Find the exact model name of your motor (read the manual and/or data sheet for your e-bike or e-scooter). Now apply the filters in the shop to your motor. Or: Read the entire guide once . In our experience, you'll know 80% more afterward than before.
We'll answer your questions in the chat: See the speech bubble in the bottom right corner. Log in to receive our reply by email; otherwise, our answer will only appear in your active browser window. If the speech bubble isn't visible, please use the second option.
2nd Mail*
Send us a message to team@ebiketuningshop.com . This is another easy way to access our fast ticketing system.
Please describe your request as precisely as possible:
Engine version
Order number
Important instructions
For initial inquiries, please always wait for a response from us first. Please do not submit multiple inquiries. We process an extremely high volume of requests daily, so longer waiting times may sometimes occur. Please also check your spam folder for our reply.
Shipping: For hardware products, you will receive an email with the tracking number on the evening of shipment. For software products, you will receive your license code after payment has been received and a short processing time has elapsed.
Invoice: The invoice will be sent to you separately by email. Please keep it for your records. The delivery note is always included with the goods.
