PearTune 4.0 for Panasonic FIT 1.0
AVAILABILITY: In stock
PRODUCT TYPE: Panasonic
BRAND: PearTune
PearTune MSO 4.0 for e-bikes with Panasonic FIT 1.0
With this tuning chip, you can completely remove the 25 km/h speed limit of your e-bike, allowing you to ride much faster with full motor support (also compatible with FLYER e-bikes with Panasonic FIT 1.0 drives). This finally allows you to fully utilize the drive's true potential.
Since this is the “4.0” version of this tuning tool, you also benefit from various additional options – for example, you can individually adjust the level of maximum engine support, lock the chip for outsiders, or set an individual activation code.
The chip must be connected using waterproof connectors in the engine compartment. Please note: During installation, approximately 7 cm of cable must be removed. Instead, the display connectors from the PearTune installed (6 pin & 8 pin).
Values on the display
Distance traveled and mileage are corrector shown.
The current speed is up to 22,3 km/h part displayed.
From 22,4 km/h to 45 km/h the correct speed can be read via the second digit and the decimal place (a 22,9 km/h display would therefore correspond to 29 km/h, 24,5 km/h would be 45 km/h etc.).
At speeds higher than 45 km/h the display remains at 24,5 km/h.
Tuning can be switched on and off
After installing the chip, you can decide whether the tuning should be active or not. Whether the car is stationary or driving, the tuning can be activated at any time by pressing the light button twice. While stationary, the tuning can also be activated using the key combination +-+-.
For confirmation, the display briefly shows the values 9.9 or 9.0 / 2.0 or 2.5 after activating / deactivating the tuning.
Advantages of the 4.0 version
In addition to the features mentioned, this 4.0 version of the PearTune Tuning chips and various additional features:
-Set your own maximum speed: The maximum assisted speed can be set to a custom value by pressing the + and - buttons. After 10 seconds of inactivity, the last selected maximum speed is automatically saved.
-Chip lock: When the chip lock is activated, the tuning chip can no longer be activated with any key. The tuning becomes virtually "invisible," preventing unauthorized access.
-Set individual activation/deactivation code.
-Tuning status when switching on the bike: With this function you can specify whether the tuning chip should be automatically ON or OFF when switching on the e-bike.
-Chip reset: If you want to install the tuning chip in another e-bike or replace the speed sensor, a chip reset is recommended. This can retain the chip settings; alternatively, the chip can also be reset to the factory settings.
-The chip does not require its own battery.
Compatibility
Compatible with e-bikes with PANASONIC mid-engines (GX0 & GX Ultimate, PowerPlus) and FIT 1.0 displays (D0 T5 etc.).
FIT 1.0 displays can be identified by designations such as "D0" or "FIT 1.0".
Example: FLYER Upstreet5 7.3 with Panasonic 36V GX Power with D0 display = FIT 1.0
Also compatible with FLYER / HERCULES e-bikes as long as they are equipped with a Panasonic motor and FIT 1.0 system.
Note: If you have a model with the new FIT 2.0 system, please select the PearTune 4.0 for Panasonic FIT 2.0.
Note: If you have a BULLS E-Bike with Panasonic drive and FIT system, it is eternity to the Fit 2.0 Variant! E-bikes from FLYER, on the other hand, are available with both FIT 1.0 and FIT 2.0 System.
If you're unsure which FIT version your e-bike is equipped with, please contact our support team before ordering! We'll be happy to help.
Distinguish between e-bikes with FIT 1.0 and FIT 2.0 systems
You can usually find out whether your e-bike is equipped with a FIT system in the manual or technical documentation for your e-bike. However, if you want to tune such an e-bike, you need to know exactly which FIT system your e-bike is equipped with.
With the FIT system, a distinction must currently be made between the “older” FIT 1.0 system, which was manufactured from 2015 to 2021/2022, and the “newer” FIT 2.0 system, which will be in use from the 2022/2023 model year.
Here we show you how to distinguish between FIT 1.0 and FIT 2.0 systems:
- Distinguishing criterion: The model year
-If your e-bike with FIT system is from the model years 2015-2021, it is definitely a FIT 1.0 e-bike (FIT 2.0 did not even exist yet).
-Starting with the 2023 model year, (almost) exclusively the FIT 2.0 system will be installed. This means: If you have a bike from 2023 onwards, it is almost certainly a FIT 2.0 system. If your e-bike is from 2024, it is definitely a FIT 2.0 e-bike.
-But beware: In the 2022 model year, and partly still in the 2023 model year, the e-bikes could be equipped with both the old FIT 1.0 system and the new FIT 2.0 system.
In this case, FIT 1.0 and FIT 2.0 can still be distinguished by their displays.
- Distinguishing criterion: The display
The general rule:
-If the display of your e-bike is equipped with control buttons (usually only 1 button), then it is a FIT 1.0 system.
-If the display has NO control buttons but a touch screen, it is a FIT 2.0 system.
-If the FIT logo appears on the display when starting the system, it is also FIT 2.0 (Note: In rare cases this also happens with FIT 1.0).
Here we show you which display types are most common in FIT systems.
Fit 1.0
-For bikes with FLYER D0/T5 Display it is always FIT 1.0.
-For bikes with FIT Center Display D1 It is FIT 1.0.
FIT 2.0
-For bikes with FIT Display Compact It is FIT 2.0.
-For bikes with FIT Display Comfort It is FIT 2.0.
On the FIT E-Bike System Integration website you can check which display you have "here"The product descriptions for the displays also state whether it is a FIT 1.0 or FIT 2.0 display. This way, you can find out for sure whether you have an e-bike with a FIT 1.0 or FIT 2.0 system.
Comparison of e-bike tuning products:
| JUM-Ped | Mountain Tuning | Badass Box | RedPed | VOLspeed | PearTune | SpeedBox | MBIQ | sIMPLEk | Sx2 dongle | |
| Art | Software |
Software |
Box | module | module | module | module |
module / Sensor |
module / Dongle |
Dongle |
| Features | ***** | ***** | * | ***** | **** | *** | *** | *** | *** / ** | * |
| Easy installation | ***** | ***** | **** | ** | ** | ** | ** | ** / * | ** / * | * |
| Invisible after installation | ***** | ***** | * | ***** | ***** | ***** | ***** | ***** | ***** / **** | **** |
| Switch on / off while driving |
* Gerät |
***** Gerät, Display |
* Essay |
***** App, Display |
***** Display |
***** Display |
***** (App), Display |
*** Display, Magnet |
***** / **** Display / Plug |
**** Plug |
| No more tuning on the bike | ***** | ***** | ***** | * | * | * | * | * | * / **** | **** |
| Invisible dismantling | ***** | ***** | ***** | ***** | ***** | ***** | ***** | ***** | ***** / *** | *** |
| Easy dismantling | ***** | ***** | ***** | ** | ** | ** | ** | ** / * | ** / * | * |
| Display correct km/h |
***** Display |
***** Display |
* |
***** Display, App |
***** Display |
***** Display |
***** Display, App |
* |
**** Display |
* |
| Dethrottling | ***** | ***** | ***** | ***** | ***** | ***** | ***** | ***** | ***** | ***** |
| Thrushes | * | ***** | * | ***** | ***** | ***** | ***** | * | * | * |
| price in euro |
169 to 249 |
189 – 349 | 139 – 164 |
219 to 239 |
159 – 219 |
139 to 259 |
139 to 349 |
89 to 199 |
89 to 219 |
139 to 159 |
Tools
To install an E-Bike tuning chip in your E-Bike it is sometimes special tools necessary. Please check previously whether you have to open the engine compartment to access the motor connectors. This is especially true for products from the Modules, Kit, Dongle and Sensor.
Normally (but not always) opening the engine compartment requires loosening the crank. To do this, you will need a Crank puller. Some engines also have a Spider Tool This is important for opening the lock ring on the chainring - because the chainring must be loosened here so that the motor cover can be removed to access the inside of the motor. If you want to replace the chainring (wear, change the gear ratio), you often need a Spider Tool. The necessary special tools can also be found in our shop. To remove the engine cover, you usually need a Torx or Allen key. For installing the modules, appropriate Pliers from the electronics sector.
Do you decide not for a tuning solution that you have to install in the engine compartment (Box, Software), there is no need for any tools. In our Guide you will find further tips.
The EBikeTuningShop and the EBikeTuningBlog We'll keep you regularly informed about the latest e-bike tuning and e-scooter tuning products and solutions. You can sign up for our free newsletter here:
warnings
Important information on tuning measures for e-bikes and e-scooters
We expressly point out that any modification to e-bikes and e-scooters – whether through hardware tuning (e.g. tuning chips, dongles, sensor adapters) or software tuning (e.g. apps, programs or USB tools) – can have consequences.
Tuning measures on e-bikes and e-scooters mean that they are no longer permitted for use on public roads as defined by the StVZO (Road Traffic Licensing Regulations). Legal use is therefore only possible on private property or - if permitted - in competitions. Riding an e-bike or e-scooter modified by tuning measures on public roads can lead to criminal liability for driving without a license (Section 21 of the Road Traffic Act) and driving without insurance (Section 6 of the PflVG). Tuning measures on e-bikes can lead to the loss of warranty rights and manufacturer guarantees. Furthermore, tuning measures can lead to the loss of insurance coverage and benefits from accident victim assistance in the event of an accident. The e-bike (or e-scooter) modified by tuning measures is subject to additional stress due to the higher speed, which can lead to safety risks.
Delivery time, shipping costs, minimum order value and payment methods:
Delivery time:
Delivery takes 1-3 business days within Germany. In exceptional cases, it can take up to 8 business days. Delivery times outside Germany may take longer. Please understand that due to high demand, some products may experience longer delivery times.
Delivery area:
We deliver to Belgium, Bulgaria, Denmark, Estonia, Finland, Germany, Greece, Ireland, Iceland, Italy, Croatia, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Austria, Poland, Portugal, Romania, Sweden, Slovakia, Slovenia, Spain, Czech Republic, Hungary, Cyprus.
For customers from Switzerland: For deliveries to Switzerland we recommend here a separate service.
Shipping:
Shipping costs for Germany are €4,90; shipping is waived for orders over €180. For countries within the EU, shipping costs are €12,90; shipping is waived for orders over €2.000. We currently do not ship to countries outside the EU. We also do not ship to the USA, France, or Canada (including any overseas territories). We ask that you bear the costs of any return shipments yourself. Please note that customs duties may apply in countries outside the European Union.
Minimum order value:
The minimum order value is €25. Only above this amount are advance payment, PayPal, and bank transfer available as payment methods.
Maximum order value:
The maximum order value for orders outside the EU is €1.000. The maximum order value within the EU is €12.500.
Payment in advance via bank transfer:
Please transfer the total amount, including your order number, to our account, which was communicated to you in the confirmation email. Please note that transfers within Germany can take up to three business days. Transfers from abroad, especially from Austria, usually reach us very quickly. Transfers from other countries can take slightly longer on average.
Payment in advance via Paypal:
At the end of the ordering process, you will be redirected to the PayPal page. There you can initiate your payment. Once the PayPal transaction is complete, your order status will change in the shop. The goods will then be shipped as soon as possible.
