SpeedBox 1.3 for Shimano EP8 / EP800 “+E-Tube Port” (Di2)
AVAILABILITY: In stock
PRODUCT TYPE: Shimano
BRAND: speed box
You save: €30,00 (14%)
SpeedBox 1.3 for Shimano EP8 / EP800 “+E-Tube Port” (Di2)
Note: This SpeedBox Tuning chip is intended for Shimano EP8 / EP800 E-Bikes without free E-Tube connection – these are usually e-bikes with one of these components:
-Satellite system ON/OFF switch
-Di2 derailleur
If your Shimano EP8 e-bike has a free E-Tube connection in the motor, please choose the standard version SpeedBox 1.3 for Shimano EP8.
The SpeedBox 1.3 is a chip that unlocks Shimano EP8 / EP8 RS e-bikes – essentially removing the 25 km/h speed limit. This allows for much faster riding with full motor support. SpeedBox 1.3 has been completely revised, including a new design and new hardware and firmware.
Important note: The manufacturer recommends not exceeding a speed of 35 km/h to avoid error W011. For B.Tuning models, the maximum speed can be adjusted in the SpeedBox App adjust accordingly.
Tuning can be switched on and off
You can turn the tuning on and off using your e-bike's light switch: Turning the light off activates the tuning. Turning the light on deactivates the tuning.
If you want, you can also use the tuning independently of the light function: In this case, you simply do not have to connect the red plug during installation; in this case, the SpeedBox Always active. Even if you don't have a light on your Shimano e-bike, the tuning is always on.
Please note: After installing the SpeedBox 1.3 chips, the e-bike display will only show correct values up to 23 km/h. If you do not want to miss out on the correct display of data such as the current speed, we recommend the SpeedBox 1.3 B.Tuning – this version of the tuning chip is compatible with the SpeedBox App, which can display the correct data on your smartphone's display while you're on the go. In this case, we recommend attaching your phone directly to the handlebars so you can easily see the data. You can find affordable mounts (LINK) in our shop.
Installation
The SpeedBox 1.3 for Shimano EP8 is a module or chip that normally needs to be plugged into the E-Tube port of the motor. The version of the chip presented here (SpeedBox 1.3 for Shimano EP8 “+E-Tube Port”) is intended for models that do not have a free E-Tube connection.
The module is connected using the original connectors. With a little skill, you can install the tool yourself and uninstall it again if necessary.
This tuning tool does not require its own battery.
Please note:
if you SpeedBox If you install the chip into a brand new e-bike, you must first ride the e-bike for at least 1 km before you start the tuning chip for the first time.
SpeedBox 1.3 for Shimano EP8 / EP800 “+E-Tube Port” (Di2) - Compatibility
Compatible with Shimano EP8 (EP800) / EP8 RS e-bike motors.
Compatible with Giant Revolt E+ e-bikes with EP8 / EP800 Engines from 2022/2023.
Important: This version of the SpeedBox Tuning Chips (“+E-Tube Port”) is intended for Shimano EP8 E-Bikes without free E-Tube connection – these are often e-bikes with one of the following components:
- E-bikes with Di2 derailleurs.
- E-bikes with a Satellite System ON/OFF Switch integrated into the frame (EW-SW100 / EW-SW300).
(If your Shimano EP8 / EP800 E-Bike has a free E-Tube connection in the motor, please choose the standard version SpeedBox 1.3 for Shimano EP8).
The tool is not compatible with the SpeedBox App
Important: Only compatible with EP-8(00) - Not compatible with EP-801!
If you have a Shimano E-Series e-bike, you will need one of the following tuning tools:
SpeedBox 1.2 for Shimano E8000, E7000, E6100, E5000
SpeedBox 1.2 B.Tuning for Shimano E8000, E7000, E6100, E5000 (with app)
Comparison of e-bike tuning products:
| JUM-Ped | Mountain Tuning | Badass Box | RedPed | VOLspeed | PearTune | SpeedBox | MBIQ | sIMPLEk | Sx2 dongle | |
| Art | Software |
Software |
Box | module | module | module | module |
module / Sensor |
module / Dongle |
Dongle |
| Features | ***** | ***** | * | ***** | **** | *** | *** | *** | *** / ** | * |
| Easy installation | ***** | ***** | **** | ** | ** | ** | ** | ** / * | ** / * | * |
| Invisible after installation | ***** | ***** | * | ***** | ***** | ***** | ***** | ***** | ***** / **** | **** |
| Switch on / off while driving |
* Gerät |
***** Gerät, Display |
* Essay |
***** App, Display |
***** Display |
***** Display |
***** (App), Display |
*** Display, Magnet |
***** / **** Display / Plug |
**** Plug |
| No more tuning on the bike | ***** | ***** | ***** | * | * | * | * | * | * / **** | **** |
| Invisible dismantling | ***** | ***** | ***** | ***** | ***** | ***** | ***** | ***** | ***** / *** | *** |
| Easy dismantling | ***** | ***** | ***** | ** | ** | ** | ** | ** / * | ** / * | * |
| Display correct km/h |
***** Display |
***** Display |
* |
***** Display, App |
***** Display |
***** Display |
***** Display, App |
* |
**** Display |
* |
| Dethrottling | ***** | ***** | ***** | ***** | ***** | ***** | ***** | ***** | ***** | ***** |
| Thrushes | * | ***** | * | ***** | ***** | ***** | ***** | * | * | * |
| price in euro |
169 to 249 |
189 – 349 | 139 – 164 |
219 to 239 |
159 – 219 |
139 to 259 |
139 to 349 |
89 to 199 |
89 to 219 |
139 to 159 |
Tools
To install an E-Bike tuning chip in your E-Bike it is sometimes special tools necessary. Please check previously whether you have to open the engine compartment to access the motor connectors. This is especially true for products from the Modules, Kit, Dongle and Sensor.
Normally (but not always) opening the engine compartment requires loosening the crank. To do this, you will need a Crank puller. Some engines also have a Spider Tool This is important for opening the lock ring on the chainring - because the chainring must be loosened here so that the motor cover can be removed to access the inside of the motor. If you want to replace the chainring (wear, change the gear ratio), you often need a Spider Tool. The necessary special tools can also be found in our shop. To remove the engine cover, you usually need a Torx or Allen key. For installing the modules, appropriate Pliers from the electronics sector.
Do you decide not for a tuning solution that you have to install in the engine compartment (Box, Software), there is no need for any tools. In our Guide you will find further tips.
The EBikeTuningShop and the EBikeTuningBlog We'll keep you regularly informed about the latest e-bike tuning and e-scooter tuning products and solutions. You can sign up for our free newsletter here:
warnings
Important information on tuning measures for e-bikes and e-scooters
We expressly point out that any modification to e-bikes and e-scooters – whether through hardware tuning (e.g. tuning chips, dongles, sensor adapters) or software tuning (e.g. apps, programs or USB tools) – can have consequences.
Tuning measures on e-bikes and e-scooters mean that they are no longer permitted for use on public roads as defined by the StVZO (Road Traffic Licensing Regulations). Legal use is therefore only possible on private property or - if permitted - in competitions. Riding an e-bike or e-scooter modified by tuning measures on public roads can lead to criminal liability for driving without a license (Section 21 of the Road Traffic Act) and driving without insurance (Section 6 of the PflVG). Tuning measures on e-bikes can lead to the loss of warranty rights and manufacturer guarantees. Furthermore, tuning measures can lead to the loss of insurance coverage and benefits from accident victim assistance in the event of an accident. The e-bike (or e-scooter) modified by tuning measures is subject to additional stress due to the higher speed, which can lead to safety risks.
Delivery time, shipping costs, minimum order value and payment methods:
Delivery time:
Delivery takes 1-3 business days within Germany. In exceptional cases, it can take up to 8 business days. Delivery times outside Germany may take longer. Please understand that due to high demand, some products may experience longer delivery times.
Delivery area:
We deliver to Belgium, Bulgaria, Denmark, Estonia, Finland, Germany, Greece, Ireland, Iceland, Italy, Croatia, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Austria, Poland, Portugal, Romania, Sweden, Slovakia, Slovenia, Spain, Czech Republic, Hungary, Cyprus.
For customers from Switzerland: For deliveries to Switzerland we recommend here a separate service.
Shipping:
Shipping costs for Germany are €4,90; shipping is waived for orders over €180. For countries within the EU, shipping costs are €12,90; shipping is waived for orders over €2.000. We currently do not ship to countries outside the EU. We also do not ship to the USA, France, or Canada (including any overseas territories). We ask that you bear the costs of any return shipments yourself. Please note that customs duties may apply in countries outside the European Union.
Minimum order value:
The minimum order value is €25. Only above this amount are advance payment, PayPal, and bank transfer available as payment methods.
Maximum order value:
The maximum order value for orders outside the EU is €1.000. The maximum order value within the EU is €12.500.
Payment in advance via bank transfer:
Please transfer the total amount, including your order number, to our account, which was communicated to you in the confirmation email. Please note that transfers within Germany can take up to three business days. Transfers from abroad, especially from Austria, usually reach us very quickly. Transfers from other countries can take slightly longer on average.
Payment in advance via Paypal:
At the end of the ordering process, you will be redirected to the PayPal page. There you can initiate your payment. Once the PayPal transaction is complete, your order status will change in the shop. The goods will then be shipped as soon as possible.
